CREATE PROCEDURE myproc(OUT s int)
    BEGIN
      SELECT COUNT(*) INTO s FROM students;
    END

SELECT routine_name FROM information_schema.routines WHERE routine_schema='數據庫名稱';

CALL myproc()

DROP PROCEDURE IF EXISTS myproc;

#檢查該存儲過程是否存在 存在就刪除了再創建
DROP PROCEDURE IF EXISTS processnames ;
#創建存儲過程
CREATE PROCEDURE processnames()
#BEGIN END  存儲過程中的sql邏輯寫在BEGIN 和END 中
BEGIN
#定義變量
DECLARE var_name VARCHAR(300);
DECLARE var_uuid VARCHAR(300);
DECLARE count int DEFAULT 0 ;
DECLARE i int DEFAULT 0 ;
DECLARE done INT;
#定義游標
DECLARE nameCursor CURSOR FOR SELECT ParentId FROM datadictionary GROUP BY ParentId;
#該sql語句作用是  在你遍歷游標的時候  游標循環結束 就會執行這句話，并給done賦值為1 然后循環就會停止 但該語句不適用WHILE 循環語句。
DECLARE continue handler FOR SQLSTATE '02000' SET done = 1;
#查詢一個表分組的總數量  并賦值給count變量
SELECT count(*) into count FROM (SELECT ParentId FROM datadictionary GROUP BY ParentId) t1;
#打開游標
OPEN nameCursor;
#循環體
    WHILE i<count DO
    #拿到游標指向的當前行的數據  并賦值給var_name變量
    FETCH nameCursor INTO var_name;
    #通過var_name變量進行相應的數據查詢 把查詢出來的數據通過into賦值給變量var_uuid
    SELECT uuid into var_uuid FROM datadictionary WHERE ID=var_name;
    #進行修改操作
    UPDATE datadictionary SET ParentId=var_uuid WHERE ParentId=var_name;
    #可以通過set 給變量賦值  這里用來記錄循環體執行了多少次  看和游標遍歷的條數是否一致
  SET i=i+1;
    #當i>count的時候循環體結束
  END WHILE;
    #關閉游標
    CLOSE nameCursor;
    #打印i 
    SELECT i;
    #查看修改后的數據
    SELECT * FROM datadictionary;
    #存儲過程結束標志
END;
#調用存儲過程
CALL processnames()

DROP PROCEDURE if EXISTS proce;
CREATE PROCEDURE proce()
BEGIN
 DECLARE  userid VARCHAR(50);
 DECLARE  depatementid VARCHAR(50);
 DECLARE  done INT; 
 DECLARE nameCuursor CURSOR FOR SELECT id,FrameworkDepartmentId FROM frameworkusers ;
 DECLARE  continue handler FOR SQLSTATE '02000' SET done = 1;
 OPEN nameCuursor;
label: LOOP
  FETCH nameCuursor INTO userid,depatementid;
    IF done = 1 THEN
        LEAVE label; 
    END IF; 
    INSERT into frameworkdepartmentuser(ID,FrameworkUserId,FrameworkDepartmentId) VALUES(UUID(),userid,depatementid);
END LOOP label;
CLOSE nameCuursor;
END;
CALL proce();
SELECT * FROM frameworkdepartmentuser

label: LOOP
?? ?statement_list

?? ?IF done=1 THEN
?? ??? ?LEAVE label;?
?? ?END IF;?
END LOOP label;