Linux中如何查看usb設備信息
更新時間：2023年06月01日 10:38:25 作者：www.wowothink.com
這篇文章主要介紹了Linux中如何查看usb設備信息問題，具有很好的參考價值，希望對大家有所幫助。如有錯誤或未考慮完全的地方，望不吝賜教
下面的信息都是在VMware中運行Ubuntu12-04系統上執行的。
同樣該命令也支持在嵌入式系統中進行USB調試。
一、cat設備節點獲取信息
在一些嵌入式開發中需要調試USB功能，經常會cat /sys 下的相關設備節點來查看某些信息，比如說我們可以看到 /sys/bus/usb/devices 目錄有多個子目錄。
進入到某個子目錄可以看到usb設備更加詳細的信息(可以理解為設備描述符)。
1、usb設備在總線上的信息
// usb設備在總線上的信息 root@ubuntu:/sys/kernel/debug# cd /sys/bus/usb/devices root@ubuntu:/sys/bus/usb/devices# ll total 0 drwxr-xr-x 2 root root 0 Nov 26 21:21 ./ drwxr-xr-x 4 root root 0 Nov 26 21:21 ../ lrwxrwxrwx 1 root root 0 Nov 26 21:21 1-0:1.0 -> ../../../devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/1-0:1.0/ lrwxrwxrwx 1 root root 0 Dec 15 23:10 1-1 -> ../../../devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/1-1/ lrwxrwxrwx 1 root root 0 Dec 15 23:18 1-1:1.0 -> ../../../devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/1-1/1-1:1.0/ lrwxrwxrwx 1 root root 0 Nov 26 21:21 2-0:1.0 -> ../../../devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-0:1.0/ lrwxrwxrwx 1 root root 0 Nov 26 21:21 2-1 -> ../../../devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-1/ lrwxrwxrwx 1 root root 0 Nov 26 21:21 2-1:1.0 -> ../../../devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-1/2-1:1.0/ lrwxrwxrwx 1 root root 0 Nov 26 21:21 2-2 -> ../../../devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-2/ lrwxrwxrwx 1 root root 0 Nov 26 21:21 2-2:1.0 -> ../../../devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-2/2-2:1.0/ lrwxrwxrwx 1 root root 0 Nov 26 21:21 usb1 -> ../../../devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/ lrwxrwxrwx 1 root root 0 Nov 26 21:21 usb2 -> ../../../devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/
其中 usbx/第x個總線，x-y:a.b/的目錄格式，x表示總線號，y表示端口，a表示配置，b表示接口。
具體解釋可以參照如下：
The names that begin with "usb" refer to USB controllers. More accurately, they refer to the "root hub" associated with each controller. The number is the USB bus number. In the example there is only one controller, so its bus is number 1. Hence the name "usb1".
"1-0:1.0" is a special case. It refers to the root hub's interface. This acts just like the interface in an actual hub an almost every respect; see below.
All the other entries refer to genuine USB devices and their interfaces. The devices are named by a scheme like this:
bus-port.port.port ...
In other words, the name starts with the bus number followed by a '-'. Then comes the sequence of port numbers for each of the intermediate hubs along the path to the device.
For example, "1-1" is a device plugged into bus 1, port 1. It happens to be a hub, and "1-1.3" is the device plugged into port 3 of that hub. That device is another hub, and "1-1.3.1" is the device plugged into its port 1.
The interfaces are indicated by suffixes having this form:
:config.interface
That is, a ':' followed by the configuration number followed by '.' followed by the interface number. In the above example, each of the devices is using configuration 1 and this configuration has only a single interface, number 0. So the interfaces show up as;
1-1:1.0 1-1.3:1.0 1-1.3.1:1.0
A hub will never have more than a single interface; that's part of the USB spec. But other devices can and do have multiple interfaces (and sometimes multiple configurations). Each interface gets its own entry in sysfs and can have its own driver.2、特定設備的詳細信息
進入到某個目錄中去，可以看到該設備的詳細信息，可用cat命令獲取信息。
// usb設備的詳細信息 root@ubuntu:/sys/bus/usb/devices/usb1# ll total 0 drwxr-xr-x 6 root root 0 Nov 26 21:21 ./ drwxr-xr-x 4 root root 0 Nov 26 21:21 ../ drwxr-xr-x 10 root root 0 Nov 26 21:21 1-0:1.0/ drwxr-xr-x 5 root root 0 Dec 15 23:10 1-1/ -rw-r--r-- 1 root root 4096 Dec 15 23:40 authorized -rw-r--r-- 1 root root 4096 Dec 15 23:40 authorized_default -rw-r--r-- 1 root root 4096 Dec 15 23:40 avoid_reset_quirk -r--r--r-- 1 root root 4096 Nov 26 21:21 bcdDevice -rw-r--r-- 1 root root 4096 Nov 26 21:21 bConfigurationValue -r--r--r-- 1 root root 4096 Nov 26 21:21 bDeviceClass -r--r--r-- 1 root root 4096 Nov 26 21:21 bDeviceProtocol -r--r--r-- 1 root root 4096 Nov 26 21:21 bDeviceSubClass -r--r--r-- 1 root root 4096 Dec 15 23:40 bmAttributes -r--r--r-- 1 root root 4096 Dec 15 23:40 bMaxPacketSize0 -r--r--r-- 1 root root 4096 Dec 15 23:40 bMaxPower -r--r--r-- 1 root root 4096 Dec 15 23:40 bNumConfigurations -r--r--r-- 1 root root 4096 Dec 15 23:40 bNumInterfaces -r--r--r-- 1 root root 4096 Nov 26 21:21 busnum -r--r--r-- 1 root root 4096 Dec 15 23:40 configuration -r--r--r-- 1 root root 65553 Nov 26 21:21 descriptors -r--r--r-- 1 root root 4096 Dec 15 23:40 dev -r--r--r-- 1 root root 4096 Nov 26 21:21 devnum -r--r--r-- 1 root root 4096 Dec 15 23:40 devpath lrwxrwxrwx 1 root root 0 Nov 27 20:06 driver -> ../../../../../bus/usb/drivers/usb/ drwxr-xr-x 3 root root 0 Dec 15 23:40 ep_00/ -r--r--r-- 1 root root 4096 Nov 26 21:21 idProduct -r--r--r-- 1 root root 4096 Nov 26 21:21 idVendor -r--r--r-- 1 root root 4096 Dec 15 23:40 ltm_capable -r--r--r-- 1 root root 4096 Nov 26 21:21 manufacturer -r--r--r-- 1 root root 4096 Dec 15 23:40 maxchild drwxr-xr-x 2 root root 0 Nov 26 21:21 power/ -r--r--r-- 1 root root 4096 Nov 26 21:21 product -r--r--r-- 1 root root 4096 Dec 15 23:40 quirks -r--r--r-- 1 root root 4096 Nov 26 21:21 removable --w------- 1 root root 4096 Dec 15 23:40 remove -r--r--r-- 1 root root 4096 Nov 26 21:21 serial -r--r--r-- 1 root root 4096 Nov 26 21:21 speed lrwxrwxrwx 1 root root 0 Nov 26 21:21 subsystem -> ../../../../../bus/usb/ -rw-r--r-- 1 root root 4096 Nov 26 21:21 uevent -r--r--r-- 1 root root 4096 Dec 15 23:40 urbnum -r--r--r-- 1 root root 4096 Dec 15 23:40 version
二、使用debugfs
1、掛載 debugfs 到 /sys/kernel/debug 路徑下
root@ubuntu:mount -t debugfs none /sys/kernel/debug
2、執行上述步驟之后
在 /sys/kernel/debug 就會生成如下的文件
root@ubuntu:/sys/bus/usb/devices# cd /sys/kernel/debug/ root@ubuntu:/sys/kernel/debug# ll total 0 drwx------ 22 root root 0 Nov 26 21:21 ./ drwxr-xr-x 7 root root 0 Nov 26 21:21 ../ drwxr-xr-x 2 root root 0 Nov 26 21:21 acpi/ drwxr-xr-x 32 root root 0 Dec 4 16:30 bdi/ drwxr-xr-x 2 root root 0 Nov 26 21:21 bluetooth/ drwxr-xr-x 2 root root 0 Nov 26 21:21 cleancache/ drwxr-xr-x 2 root root 0 Nov 26 21:21 dma_buf/ drwxr-xr-x 4 root root 0 Nov 26 21:21 dri/ drwxr-xr-x 2 root root 0 Nov 26 21:21 dynamic_debug/ drwxr-xr-x 2 root root 0 Nov 26 21:21 extfrag/ drwxr-xr-x 2 root root 0 Nov 26 21:21 frontswap/ -r--r--r-- 1 root root 0 Nov 26 21:21 gpio drwxr-xr-x 3 root root 0 Nov 26 21:21 hid/ drwxr-xr-x 2 root root 0 Nov 26 21:21 kprobes/ drwxr-xr-x 3 root root 0 Nov 26 21:21 kvm-guest/ drwxr-xr-x 2 root root 0 Nov 26 21:21 mce/ drwxr-xr-x 2 root root 0 Nov 26 21:21 pinctrl/ -r--r--r-- 1 root root 0 Nov 26 21:21 pwm drwxr-xr-x 2 root root 0 Nov 26 21:21 regmap/ drwxr-xr-x 3 root root 0 Nov 26 21:21 regulator/ -rw-r--r-- 1 root root 0 Nov 26 21:21 sched_features -r--r--r-- 1 root root 0 Nov 26 21:21 sleep_time -r--r--r-- 1 root root 0 Nov 26 21:21 suspend_stats drwxr-xr-x 7 root root 0 Nov 26 21:21 tracing/ drwxr-xr-x 3 root root 0 Nov 26 21:21 usb/ drwxr-xr-x 2 root root 0 Nov 26 21:21 virtio-ports/ -r--r--r-- 1 root root 0 Nov 26 21:21 vmmemctl -r--r--r-- 1 root root 0 Nov 26 21:21 wakeup_sources drwxr-xr-x 2 root root 0 Nov 26 21:21 x86/
3、cat 設備節點
執行下述命令之后會以特定格式打印目前USB總線上所有USB設備的信息如下：
root@ubuntu:/sys/kernel/debug# cat usb/devices T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 17/900 us ( 2%), #Int= 1, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev= 3.13 S: Manufacturer=Linux 3.13.0-32-generic uhci_hcd S: Product=UHCI Host Controller S: SerialNumber=0000:02:00.0 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0e0f ProdID=0003 Rev= 1.03 S: Manufacturer=VMware S: Product=VMware Virtual USB Mouse C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=usbhid E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=1ms T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 7 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0e0f ProdID=0002 Rev= 1.00 S: Product=VMware Virtual USB Hub C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=255ms T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6 B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev= 3.13 S: Manufacturer=Linux 3.13.0-32-generic ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:02:03.0 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=0129 Rev=39.60 S: Manufacturer=Generic S: Product=USB2.0-CRW S: SerialNumber=20100201396000000 C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=50 Driver=rts5139 E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 3 Ivl=64ms
至于信息的詳細解析可以參照 Linux源代碼中 Documentation/usb/proc_usb_info.txt 文件。
現摘錄其中對該格式的詳細解釋：
Each line is tagged with a one-character ID for that line:
T = Topology (etc.)
B = Bandwidth (applies only to USB host controllers, which are
virtualized as root hubs)
D = Device descriptor info.
P = Product ID info. (from Device descriptor, but they won't fit
together on one line)
S = String descriptors.
C = Configuration descriptor info. (* = active configuration)
I = Interface descriptor info.
E = Endpoint descriptor info.
Legend:
d = decimal number (may have leading spaces or 0's)
x = hexadecimal number (may have leading spaces or 0's)
s = string
Topology info:
T: Bus=dd Lev=dd Prnt=dd Port=dd Cnt=dd Dev#=ddd Spd=dddd MxCh=dd
| | | | | | | | |__MaxChildren
| | | | | | | |__Device Speed in Mbps
| | | | | | |__DeviceNumber
| | | | | |__Count of devices at this level
| | | | |__Connector/Port on Parent for this device
| | | |__Parent DeviceNumber
| | |__Level in topology for this bus
| |__Bus number
|__Topology info tag
Speed may be:
1.5 Mbit/s for low speed USB
12 Mbit/s for full speed USB
480 Mbit/s for high speed USB (added for USB 2.0);
also used for Wireless USB, which has no fixed speed
5000 Mbit/s for SuperSpeed USB (added for USB 3.0)
For reasons lost in the mists of time, the Port number is always
too low by 1. For example, a device plugged into port 4 will
show up with "Port=03".
Bandwidth info:
B: Alloc=ddd/ddd us (xx%), #Int=ddd, #Iso=ddd
| | | |__Number of isochronous requests
| | |__Number of interrupt requests
| |__Total Bandwidth allocated to this bus
|__Bandwidth info tag
Bandwidth allocation is an approximation of how much of one frame
(millisecond) is in use. It reflects only periodic transfers, which
are the only transfers that reserve bandwidth. Control and bulk
transfers use all other bandwidth, including reserved bandwidth that
is not used for transfers (such as for short packets).
The percentage is how much of the "reserved" bandwidth is scheduled by
those transfers. For a low or full speed bus (loosely, "USB 1.1"),
90% of the bus bandwidth is reserved. For a high speed bus (loosely,
"USB 2.0") 80% is reserved.
Device descriptor info & Product ID info:
D: Ver=x.xx Cls=xx(s) Sub=xx Prot=xx MxPS=dd #Cfgs=dd
P: Vendor=xxxx ProdID=xxxx Rev=xx.xx
where
D: Ver=x.xx Cls=xx(sssss) Sub=xx Prot=xx MxPS=dd #Cfgs=dd
| | | | | | |__NumberConfigurations
| | | | | |__MaxPacketSize of Default Endpoint
| | | | |__DeviceProtocol
| | | |__DeviceSubClass
| | |__DeviceClass
| |__Device USB version
|__Device info tag #1
where
P: Vendor=xxxx ProdID=xxxx Rev=xx.xx
| | | |__Product revision number
| | |__Product ID code
| |__Vendor ID code
|__Device info tag #2
String descriptor info:
S: Manufacturer=ssss
| |__Manufacturer of this device as read from the device.
| For USB host controller drivers (virtual root hubs) this may
| be omitted, or (for newer drivers) will identify the kernel
| version and the driver which provides this hub emulation.
|__String info tag
S: Product=ssss
| |__Product description of this device as read from the device.
| For older USB host controller drivers (virtual root hubs) this
| indicates the driver; for newer ones, it's a product (and vendor)
| description that often comes from the kernel's PCI ID database.
|__String info tag
S: SerialNumber=ssss
| |__Serial Number of this device as read from the device.
| For USB host controller drivers (virtual root hubs) this is
| some unique ID, normally a bus ID (address or slot name) that
| can't be shared with any other device.
|__String info tag
Configuration descriptor info:
C:* #Ifs=dd Cfg#=dd Atr=xx MPwr=dddmA
| | | | | |__MaxPower in mA
| | | | |__Attributes
| | | |__ConfiguratioNumber
| | |__NumberOfInterfaces
| |__ "*" indicates the active configuration (others are " ")
|__Config info tag
USB devices may have multiple configurations, each of which act
rather differently. For example, a bus-powered configuration
might be much less capable than one that is self-powered. Only
one device configuration can be active at a time; most devices
have only one configuration.
Each configuration consists of one or more interfaces. Each
interface serves a distinct "function", which is typically bound
to a different USB device driver. One common example is a USB
speaker with an audio interface for playback, and a HID interface
for use with software volume control.
Interface descriptor info (can be multiple per Config):
I:* If#=dd Alt=dd #EPs=dd Cls=xx(sssss) Sub=xx Prot=xx Driver=ssss
| | | | | | | | |__Driver name
| | | | | | | | or "(none)"
| | | | | | | |__InterfaceProtocol
| | | | | | |__InterfaceSubClass
| | | | | |__InterfaceClass
| | | | |__NumberOfEndpoints
| | | |__AlternateSettingNumber
| | |__InterfaceNumber
| |__ "*" indicates the active altsetting (others are " ")
|__Interface info tag
A given interface may have one or more "alternate" settings.
For example, default settings may not use more than a small
amount of periodic bandwidth. To use significant fractions
of bus bandwidth, drivers must select a non-default altsetting.
Only one setting for an interface may be active at a time, and
only one driver may bind to an interface at a time. Most devices
have only one alternate setting per interface.
Endpoint descriptor info (can be multiple per Interface):
E: Ad=xx(s) Atr=xx(ssss) MxPS=dddd Ivl=dddss
| | | | |__Interval (max) between transfers
| | | |__EndpointMaxPacketSize
| | |__Attributes(EndpointType)
| |__EndpointAddress(I=In,O=Out)
|__Endpoint info tag
The interval is nonzero for all periodic (interrupt or isochronous)
endpoints. For high speed endpoints the transfer interval may be
measured in microseconds rather than milliseconds.
For high speed periodic endpoints, the "MaxPacketSize" reflects
the per-microframe data transfer size. For "high bandwidth"
endpoints, that can reflect two or three packets (for up to
3KBytes every 125 usec) per endpoint.
With the Linux-USB stack, periodic bandwidth reservations use the
transfer intervals and sizes provided by URBs, which can be less
than those found in endpoint descriptor.總結
以上為個人經驗，希望能給大家一個參考，也希望大家多多支持腳本之家。
相關文章
眾所周知，網絡安全是一個非常重要的課題，而服務器是網絡安全中最關鍵的環節。Linux被認為是一個比較安全的Internet服務器，作為一種開放源代碼操作系統，一旦Linux系統中發現有安全漏洞，Internet上來自世界各地的志愿者會踴躍修補它。2008-09-09
大家好，本篇文章主要講的是linux環境下恢復rm誤刪的文件方法，感興趣的同學趕快來看一看吧，對你有幫助的話記得收藏一下哦2021-11-11
這篇文章主要介紹了Linux使用shell腳本定時刪除歷史日志文件,文中通過示例代碼介紹的非常詳細，對大家的學習或者工作具有一定的參考學習價值,需要的朋友可以參考下2020-08-08
眾所周知FFmpeg是一個開源免費跨平臺的視頻和音頻流方案，屬于自由軟件，采用LGPL或GPL許可證（依據你選擇的組件）。之前公司已經安裝了ffmpeg包，但因為時間較久，所以最近打算升級下，所以這篇文章就記錄了在centos 6.X升級ffmpeg包的詳細步驟，下面來一起看看吧。2016-11-11
Yum: 即Yellowdog Update Modifier,是一種基于rpm的包管理工具，這篇文章主要給大家介紹了關于在centos中yum命令刪除還原的補救方法，文中通過示例代碼介紹的非常詳細，對大家的學習或者工作具有一定的參考學習價值，需要的朋友們下面隨著小編來一起學習學習吧。2018-01-01
Yum中報錯：“pycurl.so: undefined symbol: CRYPTO_num_locks”的問題排查
這篇文章主要給大家介紹了在Yum中報錯： "pycurl.so: undefined symbol: CRYPTO_num_locks"的問題排查的相關資料，文中通過圖文介紹的非常詳細，需要的朋友可以參考借鑒，下面來一起看看吧。2017-06-06
rsync是一款高效的文件同步工具,支持增量同步、遠程同步、文件壓縮、權限保留等功能,它可以用于本地或遠程文件夾的同步,支持斷點續傳和排除規則,在本地模式下,可以通過cp命令替代,實現數據的增量備份,在遠程模式下2025-01-01
Linux 使用init命令實現關機，重啟，切換模式
這篇文章主要介紹了Linux 使用init命令實現關機，重啟，切換模式的相關資料,需要的朋友可以參考下2017-03-03
下面小編就為大家?guī)硪黄狪O多路復用之poll全面總結(必看篇)。小編覺得挺不錯的?，F(xiàn)在就分享給大家。也給大家做個參考。一起跟隨小編過來看看吧2016-12-12
這篇文章主要介紹了如何在linux服務器上使用tensorboard,包括錯誤記錄,本文給大家介紹的非常詳細,感興趣的朋友跟隨小編一起看看吧2024-06-06